SM-CMD3008MULTIMEDIA DVD/CD/MP3 RECEIVER with built-in 3” TFT displayInstruction manual DVD/CD/MP3- 3” TFT-
10Reverse driving cable connectionIf the rear view video camera is connected, the unit automatically switches to camera picture during reversedriving.
11Unit controlsFront panel1. POWER/TFT OFF button2. BND/NP/SUB button3. PREVIOUS button4. AF button5. TA button6. Display7. OPEN button8. USB port9. A
12Inner panel1. Disc loading slot2. SD/MMC memory card slot3. RESET button (hole)4. Panel status indicator5. EJECT buttonPressing RESET hole will eras
13Remote controller (RC)1. SETUP button2. POWER button3. ANGLE button4. ZOOM button5. STOP button6. PROG button7. STEREO button8. Cursor (UP/DOWN/LEFT
14Changing the battery1. Press the catch and at the same time pull out the battery tray (pic. 1).2. Insert the 1 lithium battery, type CR2025 (3V) bat
15General operationsReset the unitOperating the unit for the first time or after replacing the car battery, you must reset the unit. Press RESETbutton
16between the left and right speakers. Fader is to adjust the balance between the rear and front speakers.After you have reached your desired effect,
17COLOR1 (green button backlight) and COLOR2 (red button backlight). After you have reached your desiredeffect, leave the unit idle in order for the n
18Radio operationsBand selectPress repeatedly BND/NP/SUB button on the panel or BAND button on the RC to select your desired radioband in Radio mode:
19STEREO button on the RC to switch stereo reception on/off. Improvement of reception of distant stationscan be done by selecting mono mode, which may
2Dear customer!Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefullybefore connecting, operating
20PTY (Program Type)This radio will allow you to select the type of program required, and will search for a station broadcastingthat type of program.P
21 RETUNE S/L: RETUNE refers to the time period the unit allows for radio scan when reception isinterrupted. SHORT represents a time period of 30 sec
22Disc operationsInsert/Eject disc Open the front panel and insert a disc into the disc slot with label side up. The disc will be automaticallyloaded
23Play/Pause/StopDuring playback press PLAY/PAUSE button on the RC or press and hold 6/SET/PAU button on the panel topause playback. Do this operation
24input needed settings. Press ENTER button on the RC or 5/STOP/ENTER button on the panel to startplayback from the set number or time.Programming the
25Changing angle (for DVD only)Press ANGLE button on the RC to playback images at different camera angles. If a disc doesn’t supportmulti-angle playba
26USB/SD/MMC operationUSB/SD/MMC notesUSB format supports 2.0. Capacity: up to 32 Gb.For correct and satisfactory operation, licensed SD/MMC memory ca
27Setup menuPress SETUP button on the RC or 6/SET/PAU button on the panel to display setup screen, use UP/DOWNcursor buttons to select the desired set
28 PasswordChange the password. The initial factory password is 0000. You can set your own password. If you forgetyour own password, you can use 0000
29Handling and cleaning discs Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not
3Important safeguards Read carefully through the manual to familiarize yourselves with this unit. Keep this manual handy as a reference for operatin
30Troubleshooting guideBelow is a table describing simple measures that can help you eliminate most problems likely to emergewhen this unit is in use.
31SpecificationGeneralPower supply: 12 V DCMaximum power output: 4 x 50 WStorage support: DVD/DVD±R/DVD±RW, CD/CD-R/CD-RW, USB, SD/MMCCompatible forma
32!.
33 , .
34 , ,
35 , ,
36 «» ()1. 2. .3. 4.
37 – – – 1. .2
38.
39 A B1. - 1. (+)2. - 2. (-)3. - 3.
4AccessoriesReceiver 1 pcFront panel 1 pcRemote controller 1 pcFront panel protective case 1 pcISO cable 1 pcInstallation parts: Release keys 2 pcs
40 ISO A B1 - . . (+) - 2 - . . (-) - 3 - .
41 (),
421. POWER/TFT OFF2. BND/NP/SUB3. PREVIOUS4. AF5. TA6. 7. OPEN8. US
431. 2. SD/MMC3. () RESET4. 5. EJECT
44 ()1. SETUP2. POWER3. ANGLE4. ZOOM5. STOP6. PROG7. STEREO8.
451. , .2. (CR 2025 3V), .
46, . (
47 SELECT SEL :BAS () =>
48 BEEP ON () BEEP OFF (),
49 BND/NP/SUB BAND . 3 FM-
5Installation/connection Choose the mounting location where the unit will not interfere with the normal driving function of thedriver. Before finall
50 ( FM ) SELECT SEL STON (ST OFF).
51, . , TA; ;
52 PTY ; , .
53 .
54, , MEN/PBC , .
55 3/INT/, .
56 ZOOM
57 SYSTEM BND/NP/SUB (NTSC/PAL/PAL60/
58 USB- SD/MMC USB/SD/MMC-USB: USB 2.0. : 32 .SD/MMC:
59 SETUP 6/SET/PAU ;
61. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are noobstacles (wires, dashboard elements, etc) for
60 . . DVD.
61 , .
62 , ,
63....
64 12 4 50 DVD/DVD±R/DVD±RW, CD/CD-R/CD-RW, USB
72. DIN REAR-MOUNT (Method B)For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factoryradio mou
8Electrical ConnectionConnector A Connector B1. - 1. Rear right speaker (+)2. - 2. Rear right speaker (-)3. - 3. Front right speaker (+)4. Memory +12V
9ISO Connection tableFunctionLocationConnector A Connector B1 - Rear right (+) - Blue2 - Rear right (-) - Blue/White3 - Front right (+) - Grey4 Batter
Comments to this Manuals